공기 필터 테스트 표준: 제조업체를 위한 실용 가이드

There is no single air filter test standard that answers every performance question. A general ventilation filter, 에이 HEPA 필터, an engine air cleaner, and a gas-turbine intake filter may all remove particles from air, but they are evaluated for different applications and with different evidence.

The most useful starting question is therefore not “Which standard is the most advanced?” It is:

What product is being tested, and what decision must the result support?

A manufacturer may need to classify a filter, compare two designs, release a production batch, locate a leak, qualify a supplier, or demonstrate dust-holding performance to a customer. Each purpose leads to a different combination of standard, 테스트 방법, challenge aerosol or dust, 기류, instrumentation, and report.

This guide provides a practical route to the main standards used for complete air filter and air-cleaner testing.

빠른 선택 가이드

빠른 선택 가이드

This table is a navigation aid, not a conversion chart. 에이 MERV value cannot be converted exactly into an ePM group, and neither can be converted into a HEPA class or ISO T class without performing the applicable test.

Start with the Test Object, Not the Filter Shape

Start with the Test Object, Not the Filter Shape

Two filters can look similar and still require different standards. A pleated panel may be used in an air-handling unit, a vehicle intake, a gas-turbine inlet, or a cleanroom terminal housing. Its geometry alone does not define the correct test.

Before selecting a standard, identify:

• the machine or ventilation system the filter protects;
• whether the test object is media, an individual element, a complete air cleaner, or an installed filtration system;
• the rated airflow and allowable pressure drop;
• the particle-size range or dust challenge of interest;
• whether the required output is a class, a curve, a pass/fail result, or lifetime-related comparative data; 그리고
• the edition and acceptance criteria stated in the customer specification or purchase contract.

This step prevents a common mistake: selecting a familiar standard first and then trying to force the product into its method.

ISO 16890: 일반 환기 필터

ISO 16890: 일반 환기 필터

그만큼 ISO 16890 series is intended for particulate air filter elements used in general ventilation. It classifies filters according to their calculated efficiency for PM1, PM2.5, and PM10 fractions, or as ISO Coarse when the relevant ePM threshold is not reached.

The PM results are calculated from measured fractional-efficiency data using standardized reference particle-size distributions. This is more informative than assigning a filter only a broad coarse or fine label, but it should not be described as a direct simulation of every real atmosphere. Actual service performance is also affected by local aerosol composition, 습기, loading rate, installation, 유지, and operating schedule.

완전한 ISO 16890 platform may need to support:

• airflow and pressure-drop measurement;
• upstream and downstream fractional-efficiency measurement;
• the required aerosol-generation and particle-counting ranges;
• conditioning to evaluate discharged efficiency;
• gravimetric dust loading and resistance development; 그리고
• automatic calculation of the final ISO group and report.

Choose ISO 16890 when: the product is a general ventilation filter and the market or customer requires an ISO ePM or ISO Coarse 분류.

ASHRAE 52.2: General Ventilation Devices Rated by MERV

ASHRAE 52.2: General Ventilation Devices Rated by MERV

ANSI/ASHRAE Standard 52.2 is also intended for general ventilation air-cleaning devices, but it reports performance using particle-size removal efficiency and the MERV 체계. The current 2025 edition measures particle removal over the 0.3 에게 10 μm range while the device is loaded at defined intervals with standardized loading dust.

ISO 16890 그리고 ASHRAE 52.2 overlap in product category, but their aerosols, calculations, loading procedures, 분류, and reporting rules are not identical. An approximate cross-reference sometimes used for market communication is not a substitute for testing under the specified standard.

Choose ASHRAE 52.2 when: the customer, market, building specification, or product label requires a MERV rating or the ASHRAE particle-size efficiency method.

EN 1822 그리고 ISO 29463: EPA, HEPA 그리고 ULPA 필터

EN 1822 그리고 ISO 29463: EPA, HEPA 그리고 ULPA 필터

EN 1822 그리고 ISO 29463 apply to high-efficiency filters and filter media. Their central concept is performance at the most penetrating particle size, 또는 MPPS, where the filter has its highest penetration and lowest efficiency.

Depending on the filter class and applicable method, the required evidence can include:

• determination of the MPPS of the filter medium;
• integral efficiency or penetration at MPPS;
• local penetration or leak scanning of the complete filter element;
• airflow resistance at the specified test condition; 그리고
• traceable classification and test records.

These standards are closely related, but their class designations and some method rules should not be treated as interchangeable. The required measurement range also depends on the expected efficiency. 에이 0.3 μm optical particle counter used for internal production screening is not automatically a complete MPPS classification system.

Choose EN 1822 또는 ISO 29463 when: the product is an EPA, HEPA, 또는 ULPA filter and the customer requires formal high-efficiency classification, integral efficiency, or filter-element leak evidence.

Installed-system integrity testing after a filter is mounted in a cleanroom or housing is a separate activity. It should not be confused with factory classification and scanning of the filter element.

ISO 5011: Engine and Compressor Air Cleaners

ISO 5011: Engine and Compressor Air Cleaners

ISO 5011 establishes laboratory procedures for comparing air cleaners used on internal combustion engines and compressors in automotive and industrial applications. It is not limited to passenger vehicles.

Its central outputs include airflow restriction or differential pressure, gravimetric dust-collection efficiency, dust capacity, and related performance characteristics. 그만큼 2025 edition also retains provisions relevant to oil-bath air cleaners.

The basic measurement chain is gravimetric. Standardized test dust is fed into the airflow, and the mass retained by the test air cleaner and downstream collection system is used with airflow and pressure data to calculate performance. Particle counters are not a replacement for the required mass measurements.

Choose ISO 5011 when: the test object is an engine or compressor air cleaner and the required evidence concerns restriction, gravimetric efficiency, 먼지 보유 용량, or full-life laboratory comparison.

ISO 29461: A Series for Rotary-Machinery Air Intake Filtration

ISO 29461: A Series for Rotary-Machinery Air Intake Filtration

ISO 29461 should not be summarized as only “PM classification” or “real-environment simulation.” It is a multi-part series for air intake filtration used to protect stationary rotary machinery such as gas turbines and industrial compressors.

부분 1 normally concerns individual static filter elements, not direct measurement of a complete filtration system after installation in service. Its results also cannot, by themselves, predict exact field efficiency or service lifetime.

Choose ISO 29461-1 when: the filter protects stationary rotary machinery and the customer needs the applicable ISO T classification and performance data at the relevant industrial airflow.

Add another part of the ISO 29461 series when: water endurance, mechanical integrity, or coastal/offshore salt-and-humidity performance is part of the actual project requirement.

Can the Same Filter Require More Than One Standard?

Can the Same Filter Require More Than One Standard?

예. The intended market and customer evidence can create overlapping requirements.

Examples include:

• a gas-turbine intake element evaluated according to ISO 29461-1 while its lower-efficiency particle data are produced using methods derived from ISO 16890;
• an EPA 또는 HEPA intake element evaluated within ISO 29461-1 using ISO 29463-based methods;
• a general ventilation filter sold into both ISO and North American markets, requiring ISO 16890 그리고 ASHRAE 52.2 results; 또는
• a manufacturer using a simplified internal production check between full classification tests.

The reports should keep the methods and resulting classifications separate. Combining results from different standards into one unsupported “equivalent” class creates risk for both the manufacturer and its customer.

Test Equipment Must Match the Complete Method

Test Equipment Must Match the Complete Method

Listing several standards in a product brochure does not prove that a test system can perform each complete method. Before configuring equipment, check whether the platform includes the required:

• airflow range and test-section dimensions;
• mounting, sealing, and adapter arrangement;
• aerosol generators or standardized dust feeder;
• optical particle counter, submicron instrument, or gravimetric collection system;
• upstream and downstream sampling arrangement;
• 조절, 습기, water, 소금, or mechanical-stress subsystem where applicable;
• differential-pressure and airflow measurement ranges;
• balances and mass-data acquisition for gravimetric methods; 그리고
• software sequence, calculations, acceptance logic, and report fields for the specified edition.

Some standards can share airflow-control, duct, and data-acquisition infrastructure. Other methods require fundamentally different challenge and measurement chains. The equipment specification should therefore be built from the required test outputs, not from a list of standard names.

A Five-Question Selection Checklist

A Five-Question Selection Checklist

Before requesting a quotation or approving a test plan, answer these five questions:

• What is the test object? 메디아, filter element, complete air cleaner, multistage assembly, or installed system?
• What application will it serve? 일반 환기, cleanroom production, engine intake, passenger compartment, gas turbine, compressor, or offshore intake?
• What result must appear on the report? ePM group, MERV, MPPS 수업, ISO T class, local penetration, restriction, gravimetric efficiency, or dust capacity?
• At what conditions? 필터 크기, 정격 기류, resistance range, aerosol or dust, conditioning state, and final test endpoint?
• Who defines acceptance? The current standard, a customer specification, a product-development plan, or an internal production-control method?

Once these inputs are clear, the correct standard and test-system configuration become much easier to define.

SCPUR develops test systems around the evidence filter manufacturers need to produce: 분류, design comparison, production release, leak localization, dust-loading evaluation, or customer-specific validation.

Start with your filter, 정격 기류, and required report: Explore SCPUR air filter testing systems

• HVAC and General Ventilation Filter Testing Systems
• HEPA 그리고 ULPA 필터 테스트 시스템
• Engine and Turbine Intake Filter Testing Systems
• ISO 29461-1 대 ISO 5011: Which Standard Should You Choose?
• EN 1822 대 ISO 29463: 수업, 테스트 및 주요 차이점
• HEPA Filter Leak Testing: Factory Scan vs Installed-System Test

• ISO 16890-1:2016 – General ventilation filter classification
• ANSI/ASHRAE Standard 52.2-2025 – Purpose and scope
• 학사 EN 1822-1:2019 – 분류, 성능 테스트 및 마킹
• ISO 29463-1:2024 – 분류, 성능, 테스트 및 마킹
• ISO 5011:2025 – Inlet air-cleaning equipment performance testing
• ISO 29461-1:2021 – Static filter elements for rotary machinery
• ISO 29461-2:2022 – Fog and mist endurance
• ISO 29461-3:2024 – Mechanical integrity
• ISO 29461-4:2025 – Coastal and offshore environments
• ISO/TS 11155-1:2001 – Passenger-compartment particulate filtration