“ISO 16890 test equipment” does not refer to one instrument.
A complete laboratory can include fractional-efficiency measurement, 기류 저항, filter conditioning, 먼지 로딩, weighing and data-processing functions. These functions may use connected modules, but they do not all perform the same test.
The correct configuration depends on whether the laboratory needs product development, routine quality control or complete testing according to the ISO 16890 시리즈.
Define the Test Scope First
장비를 선택하기 전에, determine which results are required:
- Initial fractional-efficiency curve
- Conditioned fractional efficiency
- ISO ePM classification
- Airflow–resistance curve
- 중량 효율성
- Resistance versus captured dust mass
- 먼지 용량
- Internal production comparison
- Formal customer test report
A system configured only for efficiency and resistance testing cannot perform complete conditioning and dust-loading procedures without the corresponding modules.
1. Airflow Test Duct
The test duct provides controlled airflow through the filter.
Its configuration depends on:
- Maximum filter dimensions
- Filter type
- Rated airflow
- Required pressure range
- 시험 방향
- Available laboratory space
The duct should provide stable airflow, suitable flow distribution and low system leakage. The fan must overcome the resistance of the duct, filter and measurement components throughout the required operating range.
Airflow measurement and pressure sensors must cover both clean-filter and loaded-filter conditions.
2. Aerosol Generation and Mixing
Fractional-efficiency testing requires stable test aerosols over the required particle-size range.
The aerosol system must provide:
- Suitable particle-size distribution
- Stable concentration
- Adequate output at maximum airflow
- Effective mixing before upstream sampling
- Controlled switching and cleaning
Generator quantity and configuration cannot be selected from filter size alone. Maximum airflow and required concentration are also important.
3. Particle Measurement and Sampling
Upstream and downstream particle concentrations are measured across the required size range.
The system may require:
- Particle counters or particle-sizing instruments
- Upstream and downstream sampling probes
- Automatic sampling switching
- Dilution for higher upstream concentrations
- Controlled sampling tubing
- Background monitoring
Instrument range, resolution and counting statistics affect the efficiency result. A particle counter with the wrong concentration range cannot be corrected simply through software.
4. Filter-Conditioning Cabinet
ISO 16890 conditioning is performed in a dedicated cabinet according to ISO 16890-4.
Its purpose is to determine the minimum fractional test efficiency after reducing the influence of electrostatic charge. It is not a dust-loading process and should not be described as field-ageing simulation.
The conditioning cabinet is a separate functional module from the main test duct.
5. Dust-Loading and Weighing Equipment
ISO 16890-3 evaluates gravimetric efficiency and resistance versus captured dust mass.
The required equipment can include:
- Test-dust feeder
- Dust dispersion and injection system
- Dust preparation and handling area
- 정밀 계량 장비
- Resistance monitoring
- Exhaust or dust-collection arrangements
- Software for loading-stage data
Dust loading is separate from the ePM classification procedure. It provides comparative loading data rather than an exact prediction of field replacement time.
6. 제어 소프트웨어 및 보고
Software can coordinate:
- 공기 흐름 제어
- 에어로졸 생성
- Instrument switching
- Dilution settings
- Test sequences
- Data acquisition
- Efficiency calculation
- 분류
- Alarm handling
- 보고서 생성
Automation improves repeatability and traceability, but the calculation logic and measurement chain must still be validated.
Can One System Support Other Standards?
Some hardware may be shared between ISO 16890, ASHRAE 52.2 and legacy EN 779 테스트, 포함:
- Test duct
- Fan
- Airflow measurement
- Pressure measurement
- Part of the particle-sampling system
하지만, the standards use different aerosols, conditioning or loading procedures, calculations and report formats.
A system should not be described as compliant with several standards unless the required hardware, instruments and software procedures for each method have been verified.
Information Required for Equipment Selection
An equipment supplier should request:
- Maximum filter size and construction
- Minimum and maximum airflow
- Maximum expected pressure drop
- Required parts of ISO 16890
- Target ePM range
- Required aerosol and instruments
- Test volume and automation level
- Laboratory dimensions and utilities
- Calibration and traceability requirements
- Future ASHRAE 52.2 또는 EN 779 compatibility
SCPUR configures ISO 16890 laboratories according to the filter, airflow range and required test scope. Fractional efficiency, conditioning and dust loading are treated as connected but separate capabilities, allowing manufacturers to select the modules they actually need.
